Wildgame Innovations 6v 12v Digital Timer WGI TH DT Wild Game Innovations Outdoors

Model # TH-DX1

™

Product Information Guide

INCLUDED PARTS 1) Hopper Assembly including Lid (3 Pieces)

Poly Barrel Lid



Poly Barrel Upper



Poly Barrel Funnel

2)

Directional Power Control Unit assembly and programming instructions for this unit are contained within its box (1 piece)

3) Leg Kit Poly Barrel Leg/ Hardware/Bolt Kit

PAge 2

Silicone Rubber Gasket (1 piece)

Poly Barrel Bolt Kit (1 Kit) 5/32” Nylon Lock Nut (7 pieces)

1⁄4” Nylon Lock Nut (10 pieces)

REQUIRED TOOLS

5/32” Washer (7 pieces)

1⁄4” Washer (10 pieces)

1) Pliers 2) 1⁄4” Wrench 3) 5/32” Wrench 4) #8 Nut Driver (Hand held or for Cordless Drill)

5/32”x15/32” Bolt (7 pieces)

Production Information Guide (1 Piece)

1⁄4” x 1” Bolt (10 pieces)

Latch and striker

5) Cordless Drill – If Necessary

Hinge with pole and cotter pin

Product Decal (1 Piece) Wildgame Innovations™ Banner PAge 3

ASSEMBLY INSTRUCTIONS

1

Verify the contents of the package against the included parts list. If you are missing any parts from the list, please contact BA Products immediately at the toll-free number provided.

2

First, remove the lid and two hopper assembly pieces and then place the three pieces on the ground.

3 4 5

Second, remove both the power control unit box and the leg/bolt kit box. Open the leg kit box and locate the bolt kit and silicone rubber gasket.

Find the recess in the flange on the top side and install the silicone gasket by laying it into the recess and pressing firmly to keep it in place (Illustration A).

6

Next, locate the bolt kit and then place the top portion of the hopper onto the funneled piece. Align the bolt holes on the flanges so you can see directly through them. Insert the 1⁄4” x 1” Bolt and the 1⁄4” Washer into each hole with the head on top and the thread facing downward. Next, take the 1⁄4” Nylon Lock Nut and securely tighten to each bolt (Illustration B).

Locate the funneled piece of the hopper assembly and the silicone gasket. Lay the funneled side of the hopper piece on the ground.

(Illustration A) PAge 4

(Illustration B)

7

Locate the hinge and install it with the rounded loops facing away from the feeder. Use the 5/32” x 15/32” Bolts and 5/32” Washers. Place the bolt head on top and the thread portion toward the bottom on the inside of the hopper. Install the 5/32” Nylon Lock Nuts and tighten securely (Illustration C).

(Illustration C)

(Illustration D)

8

Place the lid on top of the hopper unit and align the hinge knuckles on the lid between the knuckles on the metal hinge. When properly aligned, you can see all the way through the combined holes. Locate the hinge pole and slide horizontally through the holes (Illustration D). Once all the way through, locate the cotter pin and install it in the hole at the end of the hinge pole and bend it to secure it in position. The lid is now installed (Illustration E).

(Illustration E)

PAge 5

9

Close the lid and then locate the latch and striker. First, take the striker portion and install it onto the lid with the j-lip facing upward. These holes are already in place on the lid so install the 5/32” x 15/32” Bolts and the 5/32” Washers with the heads on the outside of the hopper and the threads facing into the hopper. Next, place the 5/32” Nylon Lock Nuts on the bolts and tighten securely. Locate the two (2) smooth marked spots on the hopper piece. The smooth spots align vertically on the outside surface just underneath the top lip. You may have to look closely to locate the markings as they may not be real obvious.

Once located, take your cordless drill and a 5/32” drill bit and drill out the two (2) holes where the markings are located (Illustration F). Now take the latch and make sure that it is in the closed position (not extended); lay the latch portion over the j-lip to align the latch on the hopper. Now open the latch and take two (2) 5/32” x 15/32” bolts, washer and nylon lock nuts and secure the latch side into place using the two mounting holes that were just drilled. Make sure that the latch is properly aligned with the striker so when t