Stanley 77 500 Intellilaser Pro Stud Sensor & Laser Level - 77-500%20Stud%20Sensor%20Manual.pdf

114C IM 14Aug06

8/14/06

7:40 PM

77-500

IntelliLLaser Pro ™

Stud Finder and Laser Line Level with Continuous AC Warning INSTRUCTION MANUAL

Page 1

114C IM 14Aug06

8/14/06

7:40 PM

Page 2

SAFETY INSTRUCTIONS Failure to follow warnings may result in bodily injury. The following warnings must be followed to avoid injury: • DO NOT remove warning labels. • DO NOT use optical tools such as a transit to view laser beam. Serious eye injury could result. • DO NOT project the laser beam directly into the eyes of others. • DO NOT stare directly at the laser beam. • DO NOT project laser beam onto a reflective surface. • DO NOT operate around children, or allow children to operate. • DO NOT disassemble the laser. • Always turn off laser when the tool is not in use. WARNINGS: IMPORTANT: Read all instructions prior to operating the IntelliLLaser™ Pro and DO NOT remove any labels from the tool.

The 77-500 produces a straight line on the same surface on which the tool is placed. Any reflection of the line on another surface should be considered reference.

–1–

114C IM 14Aug06

8/14/06

7:40 PM

Page 3

IntelliLLaser™ Pro (77-500) Main Stud Sensing/Laser Unit The Stanley® IntelliLLaser™ Pro uses electronic signals to locate the position of studs, joists or live AC wires through drywall and other common wall materials. Once the edge of the stud has been detected, the IntelliLLaser™ Pro LCD display gives visual and audio indications that allow you to easily pinpoint the stud’s edge position. A pencil line allows you to quickly note the location of the stud edges. The Stanley® IntelliLLaser™ Pro stud sensor generates a vertical laser plane. The unit can also be tilted to produce a laser plane at any angle. The IntelliLLaser™ Pro allows the user to locate wood and metal studs through common wall materials up to 1 1/2 inches thick. The IntelliLLaser™ Pro provides automatic calibration , a backlit LCD screen, auto shut off and heavy duty ABS construction. Depth detection selected by side button for 1 inch and 1 1/2 inch.

–2–

1/ 2

inch,

114C IM 14Aug06

8/14/06

7:40 PM

Page 4

IntelliLaser™ Pro (77-500) Laser Pod The addition of the laser pod opens up the functionality of the stud finder. The unit is mountable using adhesive pads (included). Retractable feet keep the adhesive away from the surface during placement. The laser pod can be tilted ±10° once it is attached to the surface without removing the adhesive. This allows for easy repositioning of the laser plane. The laser pod can be set to level, plumb or any other angle required. With the laser pod mounted to the wall horizontally, you are free to use the main stud sensor laser pod and mark both the height and stud locations at the same time. The IntelliLLaser™ Pro laser pod generates a horizontal or vertical laser plane. It can also be mounted to the wall to reproduce any angle required. The IntelliLLaser™ Pro laser pod provides heavy duty ABS construction with large rubber pads to provide a firm grip and superior impact resistance.

Operating Instructions Battery Replacement Open the battery door on back of unit and connect a 9-volt battery (not included) to the clip. Place battery into case and snap battery door in place. It is recommended that you replace the battery when the low battery indicator is lit. Open the battery door on back of unit by sliding the door down. Slide in (2) AAA batteries (not included). Slide the battery door in place. –3–

Battery Door

ILLUSTRATION 1

Battery Door

ILLUSTRATION 2

2

114C IM 14Aug06

8/14/06

7:40 PM

Page 5

ILLUSTRATION 3

Indicator Mark Level & Plumb Vials

Live Wire LED Backlit LCD ON Button / Depth Detection Mode Selection Depth Dectection Mode Indicator

ILLUSTRATION 4

Lit When Live Wire is Lit When Detected Live Wire is Detected

ILLUSTRATION 4

Unit is Calibrating Unit is Calibrating Calibration Complete Ready to Scan Calibration Complete Ready to Scan

Low Battery Indicator Low Battery Indicator Live wire

Laser Plane ON Laser Plane ON

Live wire

Indicator Graphic Indicator Graphic

ILLUSTRATION 5

Battery Door

A