Sigma BC16.12 STS CAD wireless computer - black

Installation video:

NO

FI

DK

SE

RU

BG

Video Tutorial:

SK

SI

GB

BIKE COMPUTER TOPLINE

BC 16.12 /BC 16.12

FUNCTIONS

GB ENGLISH

1. Introduction to the BC 16.12 / BC 16.12 STS

Contents 1. Introduction to the BC 16.12 / BC 16.12 STS 1.1 Initial use 1.2 Navigation principle 1.3 Set-up

02 02 03 04

1.1 Initial use The bike computer comes in “deep sleep mode”.

2.

Functions / Properties 2.1 General 2.2 Special functions 2.3 STS features

04 04 06 06

3.

Settings / Deletion 3.1 Settings 3.2 Determining the wheel size 3.3 Deleting the functions

08 08 08 08

4. Important Notes / Troubleshooting 4.1 Technical data

09 09

5. Warranty Conditions

11

2

To exit this mode, press and hold the MODE 1 and SET buttons for five seconds. Once it has woken up, the bike computer will be in the settings menu.

1.2 Navigation principle

RESET button for – Deleting the current values – Scrolling backward

1.2.2 Assigning the functions MODE 2 button for – Switching between several functions – Scrolling forward

GB

1.2.1 Button functions

You can access the following functions by pressing the MODE 2 button: cadence / Ø cadence / time /  stopwatch / countdown timer / TS distance / TS time /  temperature / total distance 1* / total distance 2* / total distance / total time 1* / total time 2* / total time * The distinction between bike 1 and bike 2 is only displayed once a second bike has been detected.

SET button for – Switching to / from the setting mode – Scrolling backward

MODE 1 button for – Switching between the bike functions – Scrolling forward

You can access the following functions by pressing the MODE 1 button: trip distance / trip time / Ø speed / max. speed 3

1.2 Navigation principle

2. Functions / Properties

1.2.3 Display layout

2.1 General – Current / average speed comparison k If you are traveling at approximately your average speed, nothing is displayed. If you are traveling quicker than your average speed, ( ) is displayed; if you are traveling slower ( ) is displayed. This information is displayed in almost all functions, except the basic settings. – Automatic detection of the second bike k The switchover between bike 1 and bike 2 occurs automatically. You simply need to carry the necessary accessories with you. For the wired device, the universal bracket with appropriate cabling should be purchased as an extra. For the wireless device, a second speed transmitter should be purchased and set to bike 2 (see set-up instructions for further details).

Top field: Speed Middle field: Description of the functions Bottom field: Current value

1.3 Set-up Please see the leaflet provided for the set-up diagrams!

4

The total values are only separately displayed for bike 1, bike 2 and bike 1+2 once a second bike has been added. If only one bike is used, only the total values for the first bike are displayed. – Light manager k Simultaneously press the SET and RESET buttons to switch the light function on/off. The display lights up by pressing any button; the bike computer changes to the respective function when the button is pressed again. On STS devices, the light function is disabled during synchronization (max. 5 minutes). Avoid using the backlight unnecessarily to save the battery! – Service interval k The service interval informs you when you have cycled a specified number of kilometers and a bike inspection is due. This service interval can only be enabled/disabled and pre-configured by your specialist retailer. The device comes with the service interval disabled.

– Battery status k The battery status of the computer head unit is displayed shortly before “low/computer” appears the battery runs out. on the display. After changing the battery, only the time needs to be re-set. – Memory chip k Thanks to an inbuilt memory chip, all total values and settings are permanently stored in the bike computer. This means that you do not need to reconfigure any settings (except for the time) after changing the battery. – PC compatibility k The bike computer is PC-compatible. After purchasing the SIGMA DATA CENTER