RTO Waste King AH-780-UL Quick&Hot Instant Hot Water Dispenser - Tank Only

560H486P01_J:560H486P01_E

12/8/09

8:12 AM

Page 1

Tank Installation Components When you purchase the Instant Hot Water tank, tank mounting contents include:

INSTANT HOT WATER DISPENSER

quick-connect fitting

bracket

tank

quick-connect fitting with filter and cap

Materials required (not provided) 2 mounting bracket screws (and 2 plastic anchors if attaching to drywall)

1/4"

(6.35 mm) O.D. copper tubing.

Shut-Off valve and “T” fitting

Saddle valve kit to fit water supply line.

Connections must meet all local codes and ordinances. Tools and Safety Equipment you may need (not provided) • ruler or measuring tape • 13/8" drill bit - if no sink • pliers hole exists • hand or electric drill • safety glasses • small drill bit for starter holes • bucket or pan

• open-end wrench(es) • gloves • tubing cutter

Faucet Compatibility Only “Open Vent” faucets function with a instant hot water dispenser tank. Connecting a standard faucet will damage the tank and void the warranty. DO NOT LENGTHEN THE HOSE/TUBE CONNECTING THE FAUCET TO THE CENTER OF THE TOP TANK OUTLET. PERFORMANCE WILL BE IMPAIRED AND WARRANTY VOIDED.

IMPORTANT INFORMATION This hot water dispenser produces instant hot water of approximately 190°F (88°C) as dispensed from the faucet. This product is not intended to produce a continuous flow of hot water. The standard model will produce up to 60 cups of water per hour at approximately 190°F (88°C). Due to high water temperature, for safety reasons, the tank is not under pressure. Consequently, there is a slight delay of water flow after the faucet has been activated. This is normal and indicates that the expansion chamber is functioning properly. 560H486P01 REV J

560H486P01_J:560H486P01_E

12/8/09

8:12 AM

Page 2

IMPORTANT SAFETY INSTRUCTIONS PLEASE READ ALL INSTRUCTIONS VERY CAREFULLY When using electrical appliances, basic safety precautions should always be followed including the following: 1. Read all instructions. 2. To protect against electrical shock, do not place cord, plugs, or appliance in water or other liquid. 3. Do not operate any appliance with a damaged cord or plug, or after the appliance malfunctions. Return appliance to the factory for examination, repair or adjustment. See Warranty insert. 4. Do not use outdoors or in damp area. 5. Do not let cord hang over edge of table or counter, or touch hot surfaces. 6. Do not use appliance for other than intended household use. 7. When using this appliance, provide 4 to 6 inches of air space around the entire unit for air circulation. 8. Do not attempt to service this product. Repairs should be done by authorized service personnel. 9. Do not let children operate. The water can cause severe burns. SAVE THESE INSTRUCTIONS. THIS PRODUCT FOR HOUSEHOLD USE ONLY. The alert symbols displayed at right point to important safety information to make you aware of potential hazards that can cause serious injury or death. Please pay special attention to the information following these alerts and warnings. Failure to comply with these instructions can result in property damage, serious injury or death.

WARNING DANGER

ELECTRICAL REQUIREMENTS Recommended Ground Method For your personal safety, the hot water dispenser is equipped with a power supply cord having a 3-prong ground plug. To minimize possible shock hazard, the cord must be plugged into a mating 3-prong, ground-type outlet, grounded in accordance with the National Electrical Code, ANSI/NFPA 70 — latest edition* or CSA Standard C22.1, Canadian Electrical Code, Part 1, — latest edition** and all local codes and ordinances. If a mating outlet is not available, it is the personal responsibility and obligation of the customer to have a properly grounded, 3-prong outlet installed by a qualified electrician. Copies of the standards listed may be obtained from: * National Fire Protection Association One Batterymarch Park Quincy, MA 02269

**CSA International 178 Rexdale Boulevard Toronto, Ontario M9W1R3

If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determin