Pelonis WM-HO202C Oil Filled Radiator Heater

Pelonis WM-HO202C Oil Filled Radiator Heater Owners Manuals, User Guides, Instructional Help Documents & Operating Information - C:\Documents and Settings\not Alex and Natasha\My Documents\Pelonis Owner's Manual.pdf

Report DMCA / Copyright

DOWNLOAD PDF

  • 161KB
  • 6 Pages
  • 792 x 612 pts (letter)
  • 35 Downloads
  • 415 Views

 

Citation

IMPORTANT INSTRUCTIONS

PELONIS

PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS

OWNER’S MANUAL

When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:

1. 2.

3. 4. 5.

6. 7. 8.

Convection

Oil Filled Radiator Heater UL

Model HO-202C

®

PLEASE READ AND SAVE THESE INSTRUCTIONS

9. 10. 11. 12. 13. 14. 15. 16. 17.

Read all instructions before using this heater. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) from the front of the heater and keep them away from the sides and rear. Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended. Always unplug heater when not in use. Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner. Return heater to authorized service facility for examination, electrical or mechanical adjustment, or repair. Do not use outdoors. This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate heater where it may fall into bathtub or other water container. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Arrange cord away from traffic area and where it will not be tripped over. To disconnect heater, first turn controls to off, then remove plug from outlet. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked. A heater has hot and arcing or sparking parts inside. Do not use it in the areas where gasoline, paint, or flammable liquids are used or stored. Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons. Avoid the use of an extension cord because the extension cord may overheat and cause a risk of fire. However, if you have to use an extension cord, the cord shall be No. 14 AWG minimum size and rated not less than 1875 watts. This heater draws 12.5 amps during operation. To prevent overloading a circuit, do not plug the heater into a circuit that already has other appliances working. It is normal for the plug to feel warm to the touch; however, a loose fit between the AC outlet (receptacle) and plug may cause overheating and distortion of the plug. Contact a qualified electrician to replace loose or worn outlet. The output of this heater may vary and its temperature may become intense enough to burn exposed skin. Use of this heater is not recommended for persons with reduced sensitivity to heat or an inability to react to avoid burns.

18.“SAVE

THESE INSTRUCTIONS”

UNPACKING AND SET-UP INSTRUCTIONS



Place the heater on a firm level surface free from obstructions, and at least 3 ft. away from any wall and any other objects such as furniture, curtains, plants or combustible material.



With the Power and Setting Control “A” in the ”OFF” position, plug the heater into a grounded 120V outlet.



Turn the heater ”ON” by turning the Power and Setting Control “A” clockwise to your desired power setting (LOW, MED, or HIGH). The Power Indicator Light “C” will illuminate.



Turn the Thermostat Control “B” to your desired setting from “MIN” to “MAX”.

Unpack your heater and remove the wheel assemblies from the package. Refer to Fig. 1 below: 1. 2. 3. 4. 5. 6.

Make sure the heater is unplugged and in the ”OFF” position. TURN THE HEATER UPSIDE DOWN. Position the wheel base assemblies between the end fins as shown. Insert each U-shape screw into the holes of each wheel holdin