JCPenney Davinci Jacob Crib - Espresso at JCPenney

CRIB ASSEMBLY INSTRUCTIONS For Convertible Cribs DO NOT USE POWER TOOLS!

Step 1: Lay the Mattress Support Spring upside down on the floor (Scissor Lifts facing up). Unscrew the Nut and Hex Bolt at each of the four corners of the Spring. Rotate the short arm of the Scissor Lift away from the middle of the Spring toward the outside of the Spring, and screw the short arm back onto the Spring with the Nut and Hex Bolt you just removed. Repeat on each corner. This configuration puts the Spring in the highest position, which is the height recommended for newborns. To select a lower position, unscrew the Nut on the long arm of the Scissor Lift and move it closer to the middle of the Spring. The closer to the middle, the lower the mattress height will be. Step 2: Attach one of the two Stabilizer Bars to the remaining holes in the Scissor Lift with 2 Hex Bolts and Hex Wrench. Make sure the metal inserts on the Stabilizer Bar are toward the floor and the Stabilizer Bar is on the inside of the spring assembly as pictured below. Repeat for the other Stabilizer Bar on the other side of the Spring. Place a Wood Dowel in each of the holes on the ends of the Stabilizer Bars. Now flip the entire assembly over so that it rests on the Stabilizer Bars.

Steps 1 & 2

Spring and Stabilizer Bar Assembly

Step 3: Attach the Side Panels to the Spring Assembly. Insert the Dowels on the ends of the Stabilizer Bars into the top holes on the inside of the Panel. Screw the Panel into each Stabilizer Bar with a Short Decorative Bolt using the enclosed Allen Wrench. Repeat this procedure with the other Panel.

Step 3 Attach Side Panels to Spring Assembly

Step 4: Insert a Dowel in the bottom hole of each Side Panel. Attach the Front Panel to the lower part of the Side Panel Assembly using the bottom pair of holes on the Posts. Insert the Dowel on the Side Panel into the bottom hole on the post of the Front Panel using a Short Decorative Bolt on the top and bottom of the post to secure it. Repeat for Back Panel. Step 4 Attach Front and Back Panels

CONVERSION TO TODDLER BED Mattress should be in lowest position. Step 1: Remove Front Panel from the rest of the crib by unscrewing the 4 Short Bolts on the front. Step 2: Detach the Center Panel from the two Posts by unscrewing the 2 Long Decorative Bolts on each Post. Step 3: Attach the Toddler Rail in the bottom set of holes using the 2 Dowels and 2 Long Bolts that you just removed.

Step 4: Reattach the Toddler Rail and Posts Assembly back to the Side Panels using the 4 Short Bolts you removed in Step 1 of this Toddler Bed Conversion. Toddler Bed Configuration

CONVERSION FROM CRIB TO FULL BED Parts in Hardware Bag for Bed Conversion Kit 8 Long Decorative Bolts

8 Metal Collars

4 Wood Dowels

8 Nuts

6 Screws

1 Allen Wrench

o

o

Step 1: From the crib configuration, remove Front and Back Panels from crib by unscrewing the 8 Bolts connecting them to the Side Panel and Spring Assembly. Remove the Center Panel of the Front Panel by unscrewing the 4 Long Decorative Bolts going through the posts. Flip the Assembly over so the curved part of the Panel is toward the top. Reattach the Posts with the 4 Bolts. Step 2: Insert a Dowel into the center hole on both ends of each of the Bed Rails. Line up the bed rails by placing the dowel into the center of the trio of holes on each post. Attach the Bed Rails between the Front and Back Panels using 2 Long Decorative Bolts, 2 Metal Collars and 2 Nuts for each corner. Tighten the Bolts with the Allen Wrench while holding the Nut in place with your finger or a wrench. Step 3: Lay out the 3 Bed Slats on the ledgers of the Bed Rails. Space them apart evenly and screw them in to the ledgers. Full Bed Conversion

1 Back Panel

1 Front Panel

2 Side Panels

CONVERT1.wmf

1 Toddler Rail

CONVERT3.wmf

CONVERT2.wmf

CONVERT4.wmf

2 Stabilizer Bars

1 Mattress Support Spring

1 Hardware Bag (contents below)

Parts in Hardware Bag 12 Short Decorative Bolts

4 Hex Bolts

1 Hex Wrench

8 Wood Dowels

1 Allen Wrench

4 Long Decorative Bolts (already attached to front panel)

P