Fusion EN-AB1120 12" Car Subwoofer

ENCOUNTER

ACTIVE ENCLOSURES EN-AB1120, EN-AB2120

Product Specifications EN-AB1120

EN-AB2120

Max Power Rating

360 Watts

550 Watts

Frequency Repsonse

4OHz - 500Hz

35Hz - 500Hz

Bass Boost (Variable)

0 / + 18dB

0 / + 18dB

Low Pass Filter (Variable)

40Hz - 250Hz

40Hz - 250Hz

Tuning

Bass Reflex

Bass Reflex

Woofer Size

12”

2 x 12”

Fuse

15 Amp

Box Dimensions

520mm x 375mm x 405mm 20 1/2” x 14 3/4” x 15 15/16”

880mm x 375mm x 415mm 34 10/16” x 14 3/4” x 16 3/8”

Control Descriptions LEVEL This allows the adjustment of the amplifier level of the subwoofer. Turn clockwise to increase the level. If the sound becomes distorted reduce the level. LOW PASS FILTER (LPF) This allows the adjustment of the highest frequency the Encounter Active Enclosure Tube will produce. This should be adjusted to blend with your main speakers. Typically, this will be set to around 100Hz (approximately the central position of the control knob). BASS This allows very low frequencies to be boosted. Adjust with care and listen for distortion. If the sound becomes distorted, reduce the amount of boost. REMOTE LEVEL CONTROLLER When connected, this allows further control over the level from a remote location, using the supplied lead. Installation Make sure the Encounter Active Enclosure is firmly fixed in your vehicle. Check before drilling or cutting holes. DO NOT work near gas tanks, fuel lines, hydraulic lines or electrical wiring. DO NOT mount the Encounter Active Enclosure in such a way as to pinch or damage the wires. Make sure everything is firmly connected, before attaching the +12V wire. Make sure the +12V wire is fused as close as possible to the battery. ALWAYS use a fuse with the recommended rating.

Wiring • Connect the ground wire to the vehicle first (clean dirt and paint to bare metal). • Connect the 12 volt (red wire) to the positive battery terminal. Make sure the fuse is close to the battery. • Connect the remote on (blue wire) • Connect the RCA cables if applicable, OR • Connect the speaker level wire by splicing into the headunits speaker wires. See Note 1 • Connect the remote level controller with the supplied lead. • Check all connections. • Finally, connect the power plug end of the power harness to the unit. *Note 1 Take care to make sure the wires are spliced in the correct phase. Positive to positive, negative to negative. Failure to do this correctly could result in loss of bass.

Speaker Level Input Plug

FUSE HIGH INPUT

REMOTE

LOW INPUT Right

LEVEL

L.P.F

BASS

POWER PROT

Left

REM +12

L+

R+

L-

R-

Power Plug

GND

POWER MIN

MAX 40Hz 250Hz 0dB

18dB

Connect black wire to chassis ground of vehicle (Ground)

See note 1 Splice into source unit’s speaker wires (R+) Grey/White (R- ) Grey (L+ ) Green/White (L- ) Green

Connect the remote level controller lead to the amplified tube

EN-AT110

Connect red wire to positive (+12V) battery terminal Connect blue wire to source unit’s accessory lead or switched 12 volt source (REM)

Positive

Vehicle Battery

Remote Level Controller

For further product and installation information please visit www.fusionelectronics.com Para obtener más información sobre los productos o su instalación, visite www.fusionelectronics.com Weitere Informationen zum Produkt und zur Installation finden Sie auf folgender Website: www.fusionelectronics.com Ga naar www.fusionelectronics.com voor meer product- en montage-informatie Pour plus de renseignements sur les produits et l’installation, veuillez consulter www.fusionelectronics.com Per ulteriori informazioni su prodotto e installazione, potete visitare www.fusionelectronics.com За дополнительной информацией о продукции и установке обращайтесь на www.fusionelectronics.com www.fusionelectronics.com Specifications and design are subject to change without notification

RECORD YOUR PURCHASE DETAILS HERE: MODEL NUMBER __________________________

DATE OF PURCHASE__________________________

AFFIX RECEIPT HERE WARNING! Audio Systems can produce sound levels over 135dB. Continuous exposure to sound pressure levels over 100dB may cause pe