Campbell Hausfeld 5 - HP 80 - Gallon Air Compressor

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to ¢omp_ with instructions could result in personal injury and/or prop. erty damage/Retain instructions for future reference.

Air Compressors tion, that if not followed, damage to equipment.

Description Air compressor units are intended

to

provide compressed

air to power

matic tools, operate

spray guns and sup-

ply air for pneumatic

pneu-

valves and actua-

tors. The pumps supplied with these units have oil lubricated small amount

bearings.

of oil carryover requiring

vapor should

A

is present

air free of oil

have the appropriate

filter

insta[led. The air compressor units are to be mounted

per the instructions provid-

ed on a solid floor.

Any other use of

these units will void the warranty the manufacturer

Parts Manual"

to identify

compressor as single stage or two-stage.

Safety

Guidelines

This manual contains information very important This information

that is

to know and understand. is provided

for SAFETY

and to PREVENT EQUIPMENT

PROB-

LEMS. To help recognize this information, observe the following

symbols.

Danger indicates an imminently hazardous situation which, ff not avoided, will result in death or serious injury.

I_WARNINGI ardous situation

Warning indicates a potentially haz. which, if not avoided,

could result in death

or serious

After

unpacking

the unit, inspect

occurred

during

that

transit.

care-

may have

Make sure to

tighten

fittings,

bolts, etc., before

putting

unit into service.

injury.

Donotoperate unit if damaged during shipping, handling or use. Damage may result in bursting and cause injury or property damage.

General

Safety

Sincethe air compressor and other components (material pump, spray guns, filters, lubricators, hoses,etc.) used make up a high pressure pumping system, the following safety precautions must be observed at all times:

"as is" to supply breathing

consumption,

quality

of air for you must fit

the air compressor/pump

with suit-

able in-line safety and alarm equipment. This additional

equipment

necessary to properly

filter and puri-

described

in Compressed

is

Association

Commodity

Specification

G 7.1 - 1966, OSHA 29

CFR 1910. 134, and/or Standards

Canadian

Associations

DISCLAIMER

(CSA).

OF WARRANTIES

l e aI an 1 a included

with this

for the purpose

of breathing

product carefully.

application

Be thoroughly familiar with the controls and the

and alarm equipment

proper use of the equipment.

are void, and the company

2. Follow all local electrical and safety codes as well as the United States National

Electrical Codes (NEC) and

Occupational

Safety and Health Act

(OSHA). 3. Only persons well acquainted these rules of safe operation be allowed

with should

to use the compressor.

neously

and proper

air

in-line safety warranties

whatsoever

loss, personal

is used

is not simulta-

used, existing

any liability

as

Gas

In the event the compressor

5. Wear

J

is NOT

and should NOT be used

tions for Grade D breathing

injury. NOTICE

equipped

fy the air to meet minimal specifica-

4. Keep visitors away and NEVER

I

This compressor/pump

human

I_WARNINGI

Caution indicates a potentially hazardous situation which, ff not avoided, MAY result in minor or moderate Notice indicates I importantinforma-

Air Warning

air. For any application

and

will not be responsi-

ble for problems or damages resulting from such misuse. Refer to the enclosed "Replacement

Breathable

Unpacking fully for any damage

in the compressed air stream. Applications

may cause

disclaims

for any

injury or damage.

6. Do not stand on or use the unit as a handhold. 7. Before each use, inspect compressed air system and electrical for signs of damage,

components

deterioration,

weakness or leakage. Repair or allow children

replace

defective

items before using.

in the work area. 8. Check all fasteners at f