Braun K 750 CombiMax Food Processor Owners Manuals, User Guides, Instructional Help Documents & Operating Information - D:\ELECTRONICA\braun\_food_processor_®_.pdf
Citation
Service Documentation
Market Release 4/97
Braun CombiMax
K 650
3205
3205
BINC Rev: 4/97
Service Documentation Exploded Drawing 3205
BAG Rev: 11/96
3205 - 2
BINC Rev: 4/97
Service Documentation Spare Parts List 3205
BAG Rev: 1/97
Pos. No.
Part Description
1 2 3 4 5 7 9 10 11 12 13 14 15
Cover Return spring Leg spring Lever Switching PCB Coupling Housing K 650 Setting knob Switch knob Button Pressure spring Spring O-ring
3205 - 3
Part Number 3205627 3205029 3202014 3205017 3205641 3205053 3205636 3205629 3202628 3202012 3210004 3205016 3205055
BINC Rev: 4/97
Service Documentation Exploded Drawing 3205
BAG Rev: 11/96
3205 - 4
BINC Rev: 4/97
Service Documentation Spare Parts List 3205
BAG Rev: 1/97
Pos. No.
Part Description
16 17 18 19 20 20 20 20 20 21 22 23 24 25 28 29 30 31 32 33 34 35 36 37 38
Spring Carbon brush Motor cpl. Ferrite tube Wiring, black Wiring, brown Wiring, orange Wiring, red Wiring, blue Cable support Washer Damper Supporting frame Screw Gear wheel with shaft Toothed belt Screw Cable clamp Mains lead Base Rubber foot Screw Switch-PCB Switch cam Insulating tube
3205 - 5
Part Number 4227016 4227034 3205634 3205155 3205935 3205936 3205937 3205938 3205939 3205002 0111410 3205038 3205625 0033423 3202626 3205030 0028012 4206149 3205879 3205621 3205025 0033419 3205642 3205078 0818182
BINC Rev: 4/97
Service Documentation Exploded Drawing 3205
BAG Rev: 11/96
3205 - 6
BINC Rev: 4/97
Service Documentation Spare Parts List 3202
BAG Rev: 11/96
Pos. No.
Part Description
60 61 62 64 66 67 68 70 71 72 73 74 75 76 77
Pusher Lid Blade Kneading hook Safety cover Whipping attachment Bowl Grating insert Coarse slicing insert Fine slicing insert Coarse shredding insert Fine shredding insert Julienne insert Insert carrier French fries system
3205 - 7
Part Number 3200032 3200640 3200636 3200635 4293067 3200645 3200630 3200151 3200153 3200152 3200155 3200154 3200158 3200633 3200634
BINC Rev: 4/97
Service Documentation Service Information 3205
BAG Rev: 2/97
Technical Data Nominal voltage/frequency:
120V 60 Hz
Driving motor:
DC motor B2-DC
Nominal power:
approx. 600 W (load dependent)
No-load power:
approx. 100 - 140 Watts
No-load speed position 2: No-load speed position 14:
approx. 240 - 300 r.p.m. at the bowl coupling approx. 1850 - 2200 r.p.m. at the bowl coupling
Overload protection:
electronic controls, see use instructions
Mixing arm rotation:
approx. 14 - 130 r.p.m. mixing arm into the bowl approx. 144 - 1320 r.p.m. whisk into the mixing arm
Length of mains lead:
approx. 1.30 m
Note about the screws
The special screws (25/35), can only be removed with a screw driver furnished with a special blade insert. These special blade inserts for the screwdriver can be ordered from the parts department. Because of approval-board requirements and reasons of safety, only the special screws (35) into the base plate must be used to avoid tampering by un-authorized persons.
Note about the PCB
Attention, charging capacitor on the PCB (36) is charged, use a resistor of 10-50 Ohms to discharge.
Note about the wiring
All connecting cables are provided with self-securing plugs. In order be bent down slightly. These pins must not be deformed or broken off. In case that the plug does not snap in correctly to the connecting contact, a completely new cable must be used.
Note about the speed
It is not possible to adjust the speed. In case that the number of revolutions does not correspond to the technical data, the device is defective.
3205 - 8
BINC Rev: 4/97
Service Documentation Service Information 3205
BAG Rev: 11/96
Dismantling Remove all supplementary parts from the device and turn the switch to the “0” position. Exchangeable parts assembled in the housing upper part Remove the cover (1) by means of a dismantling fork (already existing for K 1000), see sketch 1. Now, the leg spring (3), the lever (4) and the switching-PCB (5) can be reached. Exchangeable Parts assembled in the housing lower part For the sake of a better dismantling, the parts in the housing upper