Bionaire Warm Mist BWM0400-U Humidifier

BWM5075/5075CIUK07EM1.qxd

6/7/07

17:06

If not available follow these instructions: 1. Repeat steps 1-3 in the Maintenance section. 2. Clean the tray by partially filling the tray with 200ml of undiluted white vinegar. If the element is heavily scaled, plug the humidifier into an electrical socket and turn it ON for no longer than 15 seconds. After this time turn the humidifier OFF and unplug it from the electrical outlet. Let solution stand 20 minutes, cleaning all interior surfaces with a soft brush. Dampen a cloth with undiluted white vinegar and wipe out entire tray to remove scale. 3. Rinse with clean warm water to remove scale and the white vinegar solution before beginning to disinfect the tank. 4. Wipe the heating element clean with a soft cloth after it has had a chance to cool. Disinfect tank: 1. Fill tank with 1 teaspoon of bleach and 3.5 litres of water. 2. Let the solution stand for 20 minutes, swishing every few minutes. Wet all surfaces. 3. Empty the tank after 20 minutes, and rinse well with water until the bleach smell is gone. Dry with some paper towel. 4. Refill the water tank with cool water; replace the water tank. Repeat Operating Instructions. Storage Instructions If your humidifier will not be in use for two days or more, or at the end of the season follow these instructions. 1. Clean, rinse and thoroughly dry the humidifier as directed in the De-scaling Maintenance section. DO NOT leave any water inside the base or tray. 2. Remove the reservoir cap. Do not store with the reservoir cap in place. 3. Remove and throw away the filter. 4. Place the humidifier in the original carton and store in a cool, dry place. 5. Clean the humidifier before the next season begins. 6. Order a replacement filter to start the next season. SERVICE INSTRUCTIONS 1. Do NOT attempt to repair or adjust any electrical or mechanical functions on this unit. Doing so will void the warranty. The insides of the unit contain no user serviceable parts. Only qualified personnel should perform all servicing. 2. Should the unit stop working, first check the fuse in the plug (UK only) or fuse/circuit breaker at the distribution board is operating,

Page 1

•

before contacting the manufacturer or service agent. 3. If you need to exchange the unit, please return it in its original carton, with a sales receipt, to the store where you purchased it. 4. Should your humidifier require service, please contact your local dealer. ACCESSORIES FOR MODEL BWM5075 • WMF-50 Water Purification Filter. • We recommend the use of a Bionaire® Hygrometer/Thermometer, model no: BT400, to read the indoor room temperature and humidity level. • Bionaire® Cleaning Solution. TECHNICAL SPECIFICATIONS Input voltage: 220-240 V~ 50 Hz Power consumption: 400 Watts (max) The manufacturer reserves the right to change or modify any specifications without notice. For U.K. and Ireland only: If the plug is not suitable for the socket outlets in your home, it can be removed and replaced by a plug of the correct type. Please refer to "Installation of a plug" below. Installation of a plug Applicable to U.K. and Ireland. WARNING - THIS APPLIANCE MUST BE EARTHED The wires in the mains lead are coloured as such: GREEN AND YELLOW - EARTH BROWN - LIVE BLUE - NEUTRAL Please note that the colour of these mains wires may not correspond with the colour markings that identify the terminals in your plug. Please proceed as follows: The wire which is coloured GREEN AND YELLOW must be connected to the terminal which is marked with the letter 'E' or by the earth symbol or coloured GREEN or GREEN AND YELLOW. The BROWN coloured wire must be connected to the terminal, which is marked with the letter "L" or is coloured RED. The BLUE coloured wire must be connected to the terminal, which is marked with the letter "N" or is coloured BLACK.

•

• NOTE: If the terminals in the plug are not marked or if you are unsure or in doubt about the installation of the plug please contact a qualified electrician. If a 13A 3-pin plug is fitted, it must be an ASTA approved plug, conforming to BS1363 standard.