AT&T ATT-992 Corded Phone - 922_manual.pdf

User’s Manual for the Two-Line Speakerphone 922 Fold open this manual for information about this telephone’s installation and operation. Please read Part 1 — Important Product Information, included in this package.

Part 2 © 1998 Philips Consumer Communications, L.P. All rights reserved. Printed in Mexico. 848235974 Issue 1AT&T

IN CASE OF DIFFICULT Y • Try calling the number you want to enter into memory. When the call is ended, press , and a memory button. • If someone lifts an extension phone while you are storing numbers in memory, programming might be interrupted. Make sure all extensions are on hook while storing numbers in memory. • You might not hear the confirmation beep if the RECEIVER (handset) volume is set too low, or if you are in a noisy location. • If the number is more than 24 digits long, make sure you follow the directions for “Dialing Long Numbers.” • Do not put the phone on Hold while storing numbers.

Problems With Line Status Lights • Make sure all plugs are connected properly. Inspect the line cord connections at the modular jack and at the telephone. Also inspect the coiled handset cord connections at both ends. • Try replacing old batteries. See “Batteries” in the Installation section. • Make sure the batteries are correctly installed, and that the battery contact surfaces and battery case are clean. • If only one telephone line is connected, make sure that only the batteries for that line (as labeled on the battery compartment) are installed.

6

Telephone Does Not Ring • Make sure the RINGER switch is set in the LO or HI position. • If there are several other telephones on the same line, try disconnecting some of the other telephones. Having too many telephones connected can also create problems such as low ringer volume, or impaired sound quality during calls. Other Problems Make sure you have followed all the instructions in this booklet. If you continue to have problems, call 1 800 722-9125. If you cannot correct the problem, disconnect the telephone and refer to the warranty information.

I N S TA L L AT I O N NOTE: This telephone requires a 2-line modular jack or two separate one-line modular jacks to use this unit as a two-line phone. NOTE: To use both lines of a twoline telephone, your local telephone company must provide two telephone numbers. Batteries NOTE: The base must be removed to install batteries.

Before using the telephone, you should install AA batteries (not included). If you are connecting only Line 1 or only Line 2, use two batteries, as indicated on the bottom of the phone. If you are connecting both lines, use four batteries. You can use the phone without batteries to make and receive calls, but it requires batteries to power the Line Status lights.

If you have wall-mounted the telephone, follow these directions: 1 Remove the telephone from the wall. 2 Turn the telephone upside down. 3 Remove the base by pressing the tabs located on the top of the base. 4 Press down on tab on battery door located between arrows on battery door (Figure 2A). Swing door open and insert new batteries (Figure 2B). 5 Close the battery door. CAUTION: Always unplug the line cord before installing new AA batteries.

Accesses memory dialing numbers

Directory Card/Cover Line Status Lights

One-Touch Memory Locations Two Touch Memory Locations

Line selection Programs a number in memory

Line 2 Ringer Volume

Conferences both lines

Accesses two-touch memory dialing numbers

Programs a pause in memory Access Call Waiting or other services

Line 1 Ringer Volume Puts a call on hold

Handset

Mutes a call Redials last call made, or starts Auto Redial

Temporary Tone

Speaker/Handset Volume Turn speaker on or off

Figure 1

Press down on tab to open battery door

Insert two AA batteries for Line 2

BATTERY DOOR CLOSED, BASE OFF

Figure 2A

BATTERY DOOR OPEN, BASE OFF

Figure 2B Insert two AA batteries for Line 1 1

I N S TA L L AT I O N continued Table 1 Remove the base. 2 Connect line cord(s) to telephone. • If you have a two-line jack, use only the line cord with the clear modular plugs on each e